Key takeaways
- ✦Never pressure wash anything that may contain asbestos. It is illegal in every state.
- ✦Get advice before washing flaking paint on a home built before 1970.
- ✦Painted walls, render, old brick, timber and Colorbond need a gentler method.
- ✦Never use a pressure lance from a ladder or near power points.
- ✦Keep wash water and detergent out of the stormwater drain.
Quick answer
Don't pressure wash anything that may contain asbestos, flaking paint on an older home, soft or crumbling brickwork, timber that is already rough or splintered, or anything near power points and switchboards. These materials can break up, spread contamination or let water in when they're hit with a strong jet. Many of them can still be cleaned safely with a low-pressure soft wash, a brush and the right detergent, or not at all until a specialist has checked them. Use the checklist below before you or anyone else starts.
Stop first: asbestos and lead paint
Two materials need a check before any washing at all.
Asbestos. The ACT Government advises that any ACT home built before 1990 may contain asbestos, and it lists high-pressure water blasters as a tool that can release large amounts of fibres. Using high pressure water spray or compressed air on asbestos materials is illegal in every state of Australia, according to the Asbestos and Silica Safety and Eradication Agency. SafeWork NSW warns that it can cause widespread contamination, and that the damage can reach neighbouring homes too. Fibro roofs, eaves, fences and wall sheeting are the usual places to look.
If you're not sure, don't wash it. Queensland's asbestos authority suggests applying a fungicide and sealant to asbestos materials instead of cleaning them.
Lead paint. The Australian Government's Lead Alert guide says homes built before 1970 are most at risk of lead paint, although newer homes can contain it too. The guide warns against blasting, dry scraping and dry sanding, because the paint particles can be breathed in or settle around the home. If older paint is flaking or peeling, talk to a painter about lead-safe preparation before anyone washes the wall.
Surface by surface: what high pressure can damage
| Surface | What a strong jet can do | Safer approach |
|---|---|---|
| Fibro (asbestos cement) roofs, eaves, fences and walls | Release asbestos fibres and contaminate the property | Don't wash; get specialist advice |
| Painted walls and render | Strip paint, mark render and force water behind it | Low-pressure soft wash |
| Older or soft brick and mortar | Erode the brick face and wash out mortar joints | Water and a bristle brush, or low pressure after a test patch |
| Timber decks and fences | Raise the timber fibres and cause splinters | Deck cleaner or detergent with a brush |
| Colorbond walls, fences and roofs | Scuff the painted finish | Mild detergent, soft brush, clean rinse |
| Roof tiles | Damage tiles or pointing, or push water under them | Pre-treatment and a gentle rinse |
| Windows, seals and frames | Force water into seals and gaps | Hand cleaning or low pressure |
| Power points, lights and switchboards | Let water into live electrical parts | Keep water well away |
| Sound concrete driveways and paths | Usually handles a firm clean | High pressure with a rotary surface cleaner |
A few notes on the trickier surfaces:
- Brick. Heritage Victoria says plain water is generally the simplest and safest way to clean masonry, starting with a firm bristle brush. It warns that pressure cleaning needs great care to avoid damaging the surface and the pointing, that weak surfaces are damaged more easily, and that you should always test a small area first.
- Timber. Building research body BRANZ advises against waterblasting timber decks, because the jet raises the fibres and causes splinters. It suggests detergent, hot water and a scrubbing brush instead.
- Colorbond. BlueScope's care advice is to wash Colorbond steel with a mild soap or non-abrasive detergent, using a sponge, soft cloth or soft nylon brush, then rinse well. It says never to use abrasive or solvent cleaners such as turps or paint thinners.
The risks to people, not just surfaces
Injection injuries. WorkSafe Victoria warns that a high-pressure water jet can pierce the skin, inject contaminated material into the body and throw debris into your eyes. Never point the lance at anyone, wear eye protection and enclosed shoes, and get medical help straight away if the jet breaks the skin, even if the wound looks small.
Ladders and roofs. The NSW Agency for Clinical Innovation says ladders are linked to more deaths and serious injuries around the home than any other product, and that a fall of 1–2 metres can be enough to cause serious injury. The kick from a pressure lance can push you off balance, so never use one from a ladder or on a roof.
Electricity. The NSW Government says not to mix water and electricity, and notes that shocks in wet areas are more likely to be fatal. Keep the spray away from power points, outdoor lights, the meter box and air-conditioning units.
Cleaning products. The Better Health Channel warns that chemicals can create a poisonous gas or liquid when mixed. Read the label, use the recommended gloves, goggles and mask, work in a well-ventilated area, and never mix products.
Water rules and stormwater in Canberra and Queanbeyan
Under Icon Water's permanent water conservation measures, you can clean paved areas at any time with a bucket and mop or a high-pressure low-volume cleaner. Windows and the outside of buildings can be washed with a bucket and mop or brush, a squeegee or a high-pressure low-volume cleaner, but not with a standard garden hose. The same measures apply in Queanbeyan, Jerrabomberra and Googong, which are supplied by Icon Water, according to Queanbeyan-Palerang Regional Council.
Where the water goes matters too. The ACT Government notes there is no treatment plant for the stormwater system, so dirty water and detergent that enter a street drain flow on to local waterways. Sweep up first, use only the product you need, and keep the wash water out of the drain.
Pre-clean safety checklist
Work through this list before any outdoor cleaning. You can also download the printable version below to keep with your cleaning gear.
- When was the home built? If before 1990, check fibro roofs, eaves, fences and wall sheeting for asbestos before washing them.
- Is any paint flaking or peeling? On a home built before 1970, get advice on lead-safe preparation first.
- What is the surface? Match the method to the material using the table above.
- Is anything already damaged? Look for cracks, loose pavers, soft mortar, lifting paint and loose roof tiles.
- Have you tested a small hidden area? Check the result before you do the whole surface.
- Are power points, lights and the meter box protected? Keep water well away from them.
- Will you need a ladder or the roof? If so, don't use a pressure lance. Call a professional instead.
- Have you read the product label? Never mix products, and wear the recommended protective gear.
- Are people, pets and plants protected? Keep them clear, water nearby garden beds and cover delicate plants.
- Where will the water go? Sweep up first and keep wash water and detergent out of the stormwater drain.
Pre-clean safety checklist (PDF)
Free 3-page printable and fillable checklist: asbestos and lead paint checks, surface guide, safety steps and water rules for Canberra and Queanbeyan.
When to call a professional
It's worth calling a professional when the surface may contain asbestos or lead paint, when the job needs a ladder or roof access, when walls are painted or rendered, or when you're not sure the surface can take the pressure.
At Aussie Duo Cleaning Service, we start every pressure cleaning job by checking each surface for cracks, loose pavers and flaking paint, and we talk through any existing damage with you before we begin. Our policy is that we don't clean anything that may contain asbestos. We soft wash painted walls, render, eaves and Colorbond on single-storey homes, we clean timber decks and other outdoor timber, and we treat moss and mould on single-storey concrete tile, terracotta and Colorbond roofs. For sound concrete and pavers, our high pressure cleaning service uses a rotary surface cleaner set to suit the surface. If you're comparing methods, our guide to pressure washing vs soft washing explains the difference.
Call us on 02 5501 3316 or request a quote online. We usually reply within 30 minutes during business hours, Monday to Saturday, 7am–7pm.
Frequently asked questions
📝 References & sources
- ACT Government – Asbestos
- Asbestos and Silica Safety and Eradication Agency – Asbestos cement roofs
- SafeWork NSW – Pressure cleaning of asbestos roofs safety alert
- Workplace Health and Safety Queensland – Don't use high pressure water blasters on asbestos
- Australian Government – Lead Alert: The six step guide to painting your home (5th edition)
- Heritage Victoria – Cleaning masonry
- BRANZ – Timber decks: common problems and repairs
- BlueScope – Maintain COLORBOND steel and ZINCALUME steel
- WorkSafe Victoria – High-pressure water jetting
- NSW Agency for Clinical Innovation – Home ladder safety
- NSW Government – Avoiding electrical accidents
- Better Health Channel – Chemicals in the home
- Icon Water – Permanent Water Conservation Measures: rules for residents
- Queanbeyan-Palerang Regional Council – Water restrictions and conservation measures
- ACT Government – H2OK: keeping our waterways healthy
Share Your Experience
We'd love to hear your thoughts about this article


